I won't bother with lattice, barrels are partially obscured from the street by fencing and if I put it up I would have to work around the lattice in order to turn the valves for water. If I can just make better use of collected water I'll be happy. We are at the end of our growing season so I should be cleaning up the garden and putting it to bed for the winter, just can't seem to get motivated. We had our first frost last week. Usually, our average early frost date is 1 November. I got almost no produce from garden this year, but there is always next year. Chookchook2 I've seen some of those decorative metal panels and they are gorgeous, sure hope your budget will allow you to get some before too long. Most of our state has been on fire for a good part of the summer. The closest is across the river from us and they have been battling it for almost a month. Some friends have had to evacuate repeatedly. We've only been concerned once, a small grass fire on our side of the river on a day we had wind gusts up to 65mph. Fortunately, it was put out quickly. Australia and New Zealand have both sent firefighters to help with the blazes. I can't begin to tell you how appreciative we are. The closest fire was fought for almost a week by local volunteers only as there were no other resources available. They were all on other fires. The Army National Guard (reserve troops) were called out to help with support duties and for the first time ever the federal Department of Natural Resources (DNR) asked for civilian volunteers to help with non firefighting tasks, cutting fire breaks, moving supplies etc.

You have "wear through" which is when the finish is pierced and the wood is exposed to the elements. The dark areas are where dirk/water/mud have stained the floor. It is possible to get this out... but probably not all the way. A floor that has wear through needs to be sanded right down, stained (if you wish) and then refinished. Patching can occur...but it is almost always a waste of time because the "look" can be very different from the original sitting right next to it. I don't recommend it for your situation. The second photo shows the deep scratching. Ideally, you would have had your floors looked after BEFORE wear-through occurs. There are some "regular" scratches to the Left in photo 2. You can see it is visible...but no discolouration....THAT is where you draw the line. The darker "wear through" to the Right in photo 2 = too late = full sand and refinish. If you catch it BEFORE wear-through, you can do a "buff and coat". This is a light sanding with a few coats of high end finish over top. The buff and coat is roughly half the price (in Canada at least) as a full sand/refinish. For this reason it is important to catch the floors before you get to this level of scratching.. That being said, you now get to pick some stains (test patch, test patch, test patch). The first photo shows two different woods...you could ask to see if the lighter would could be matched to the darker wood (lots of testing to achieve this). It won't be pefect...but then again you wouldn't have used reclaimed building materials if you were after "perfect". The match can lessen the colour variation to a more manageable (design wise) level. As for "good for dogs" - natural colour of wood = best colour for scratches. A lower gloss (like a satin) can help. You can ask for the "best" finish with scratch resistance that comes in a can. You will pay a premium for it...but it could/should save you thousands of dollars over the long run. A highend, scratch resistant finish means you can get away with the cheaper buff and coats (every 7-12 years...or so) and be able to retain the original (expensive) finish for the full 25 years. The other thing to note: dogs claws require trimming 2-4 PER MONTH when working with hardwoods. This is what the hardwood flooring refers to as "routine" trimming. Some of my clients thought "2-3 PER YEAR" was "routine". I laughed. You have heavy, high energy, powerful dogs. A single lab can cause some damage over time. Two labs can do a number on a floor. Three labs and you have a very short lived hardwood finish. You have 7. I would find the most expensive, scratch resistant finish available in Australia. I would have the maximum amount of finished put your floors (you will pay extra) it and I would budget for a "buff and coat" every 5-7 years.

OK - I'm a beginner here on Houzz so my opinion isn't worth a lot but here it is: the room is a bit bland and lacking in character. I think you have to find some pieces you really love to bring it alive. All the suggestions are good for widening your horizons, but ultimately, you need to find things that matter to you, because it's your home and not a magazine photoshoot. That said, if it were me, I'd throw a couple of small, colorful rugs down, and put either one large painting or three smaller ones over the bed - not in a line but at different heights - to break up the binary look. I'd also put something on the wall above the heater. Then, play around with a few cushions and maybe a quilt that picks up some of the colours in your artwork.

I read an interesting comment somewhere, where a lady invited a group of her friends over to lovingly point out all the problems they saw (through fresh eyes) with her home on preparation for sale. She said she was surprised at marks and damage that she had lived with for so long she no longer noticed them. We "owner built" a home previously, and when we came to sell 7 years later, we painted the garage and did those jobs that we had put off, and it became sad to finally see her at her best, at the end, when we could have been living in a completely finished home all that time. I read about a lady who decluttered her home, had it professionally cleaned (build clean, or bond clean) and had a professional styler do her home and she realised just how nice it could be and decided not to sell. :) ta