I think the roof might be a bit too dark for the brick colour. The bricks and the window joinery will blend in fine. What did you decide to do?

You have "wear through" which is when the finish is pierced and the wood is exposed to the elements. The dark areas are where dirk/water/mud have stained the floor. It is possible to get this out... but probably not all the way. A floor that has wear through needs to be sanded right down, stained (if you wish) and then refinished. Patching can occur...but it is almost always a waste of time because the "look" can be very different from the original sitting right next to it. I don't recommend it for your situation. The second photo shows the deep scratching. Ideally, you would have had your floors looked after BEFORE wear-through occurs. There are some "regular" scratches to the Left in photo 2. You can see it is visible...but no discolouration....THAT is where you draw the line. The darker "wear through" to the Right in photo 2 = too late = full sand and refinish. If you catch it BEFORE wear-through, you can do a "buff and coat". This is a light sanding with a few coats of high end finish over top. The buff and coat is roughly half the price (in Canada at least) as a full sand/refinish. For this reason it is important to catch the floors before you get to this level of scratching.. That being said, you now get to pick some stains (test patch, test patch, test patch). The first photo shows two different woods...you could ask to see if the lighter would could be matched to the darker wood (lots of testing to achieve this). It won't be pefect...but then again you wouldn't have used reclaimed building materials if you were after "perfect". The match can lessen the colour variation to a more manageable (design wise) level. As for "good for dogs" - natural colour of wood = best colour for scratches. A lower gloss (like a satin) can help. You can ask for the "best" finish with scratch resistance that comes in a can. You will pay a premium for it...but it could/should save you thousands of dollars over the long run. A highend, scratch resistant finish means you can get away with the cheaper buff and coats (every 7-12 years...or so) and be able to retain the original (expensive) finish for the full 25 years. The other thing to note: dogs claws require trimming 2-4 PER MONTH when working with hardwoods. This is what the hardwood flooring refers to as "routine" trimming. Some of my clients thought "2-3 PER YEAR" was "routine". I laughed. You have heavy, high energy, powerful dogs. A single lab can cause some damage over time. Two labs can do a number on a floor. Three labs and you have a very short lived hardwood finish. You have 7. I would find the most expensive, scratch resistant finish available in Australia. I would have the maximum amount of finished put your floors (you will pay extra) it and I would budget for a "buff and coat" every 5-7 years.

It looks great ! As the house is lighter and darker greys , I'd add a white gloss painted 'rail' around the top -- hard to tell appropriate sizes from the photos , but probably pine 150-200mm wide and 60mm tall . Easiest would be to simply nail it to the posts and top rails , but if you added some spacers ( cut some 100 x 50 pine into 100mm lengths , then stain them the same dark grey fence colour , nail to the posts and probably every 'halfway' too , it would really 'lift' it more ? IMO that would really tie it all in with the house , and look classy , for maybe $2k tops .

Hi. We moved into our home in Central Otago in 2013. It had been built around 2000 and clad with Oregon and Plaster. It was evident that this house was tired with the most pressing need the rescuing of the Oregon cladding. It was well overdue for a recoat. On much appreciated advice from a Resene Rep we bleached (Moss and Mould Killer) and scrubbed (Timber and Deck Wash) then coated with Resene Waterborne Woodsman in Nutmeg with CoolColour, This took up my summers of 2014, 2015 and part of 2016 the remainder of which was taken up overhauling the plaster. This summer I have tied in the entrance slat fence. Unfortunatelyn we were let down by Resene in early 2015 with an unannounced change of formula resulting in out of stocks and worst of all colour changes. Nutmeg which previously was a warm brown definitely moved into the orange spectrum. Resene WW is meant to be recoated every 18-24 months so strictly speaking I can't physically keep up with the staining let alone have a life as well. Stripping back is not an option, no no no. What compatible product would you recommend that definitely lasts longer than Resene WW? Where can I find LRV for Resene WW in case I need to stick with that but change the colour? Sadly I can't find information on comparing products across brands as reps only compare between their own products. Many thanks.