Hello people, Question time again. Im trying to match indoor and outdoor colour to my project around the living and pool area. I have 10 Meters of space to work with which includes 5 meters width of the living area. If i break the colours indoor v's outdoor it will make my area look smaller, more confined ? If i use polished concrete inside and try and match the colour outside, the surface will get hot. Soooooo... I have added some photos here. I went and purchased a box of man made granit tiles 80x 80cm. Keeping the shiny for the inside and tried "honing" the surface of the other tile as a test so i could use it outside and keeping the surface of the 'honed tile" slightly textured to ensure not so slippery and matching the inside colour. After coating this honed tile it has gone slightly darker which is ok. What im wanting to know, is this ok to do ? will there be any down the line effects of the tile if its outside in a wet area ? it maybe only wet for 3 months of the year for a few hours at a time. My challenge here is price V's product / Styling / practacality -Timber is too expensive for outdoor application / requires maintenance -Marble expensive -Natural stone expensive also if anyone has any solutions / kmowledge / advice it its ok to hone an indoor tile and add a protective coating for the outside. this would be much appreciated. Thanks Houzz'ers! Justin :)

Lighting - pendants over the servery bench should be another feature that complements your chosen kitchen surfaces. So whilst I love the copper pendants in picture 1.. They could work depending on the rest of your decor and would be a highlight in a neutral white/timber kitchen = Good! If you choose copper you would complement it with a couple of copper bench top items. These are beautiful! (I collect copper because I love it, my kitchen pendants are silver, I renovated to sell in the next 3-5 years) You will see a picture starting to form in your mind and there is nothing wrong with making a statement with your lighting. I found that when I wasn't sure I would get a very strong sense of what was right and what was wrong for a space, then common sense or passion would determine the outcome! Here are another couple that might work, look her on Houzz under lighting, search pendants, then have fun looking!Timber tones with black or white to complement your cabinets... or Statement white pendants for a bit of quirky fun! Your personality can be reflected in your lighting and accessories creating that point of difference from the predictable white on timber look. Plus don't forget the power of greenery to punctuate the theme!

I love the look of Tand G as the real thing or the 'James Hardie' NZ groove panels..........but also want my ensuite to look opulent. I am not having tiling anywhere in this room, which would be the easiest solution. Hence my dilemma..... I already have chosen the white 'tile look' acrylic walls with a feature 'marble' (narrow) panel in the shower alcove enclosure from the 'Atlantis' range. The alcove covers the complete width of the bathroom so is a feature in itself. I wanted to bring the 'marble 'feature' into the room if I could to enhance the opulence. The marbling is minimal veining on a white background so not too dramatic a feature. The obvious area is to use a matching 'marble' vanity top and/or a splash back (especially if have a china vanity top, which is the more likely due to cost). Where should the splashback end at the sides? I thought about taking the 'marble' splashback above the mirror to the ceiling thus creating a similar panel feature to that in the shower albeit wider but don't know how much wider it should be than the vanity. Also What then to do on the rest of the wall(s)? Just painted gib? If I used T& G or groove panelling I would want it to reach the ceiling. So do I put T&G on on all walls? The vanity wall has approx 1000mm 'strips' of full wall either side and the strips below the vanity and above mirror if only a splashback is incorporated. The opposite wall is almost taken up by window, radiator below, btw toilet and towel rail, leaving little wall to 'feature' and then the remaining wall is narrow (only 1100 left after door). These remaining walls could just be left as painted gib of course as really cannot afford to take the 'marble' panelling anywhere else in the room nor think where else it would feature best. 'Marble' Flooring is a possibility but it would need to be vinyl not porcelain tiles. Having written all this down I think I have talked myself out of T&G on any of the walls as the narrow room would become too busy and bitty but am still interested in what others think.

Hi We are torn between a black and a white bathroom vanity. Here are the details of the bathroom: Large marble tiles on floor and up walls. With large round mirror above vanity One feature wall in charcoal hexagons Chrome tapware Concrete basin. We are wondering whether to put the basin on a white concrete top and white vanity front (safe!) OR Black vanity with either white or black top. Love the idea of a black vanity- I think it would really pop with all the grey/white in the tiles/basin etc but would it look odd with a white top (so 3 diff colours grey basin/white top/black vanity front) Better to have a black top? Anyone got an examples to show me? Thanks