I have just taken a couple more pictures (excuse the untidy house) from the stairs. As you can see it's an open plan area that isn't that big but very high ceilings also in wood (Macrocarpa) with dark wooden beams. The house is surrounded by bush so quite a dark house. I initially considered a darker wood similar to the beams but not sure if that will make the house appear smaller / darker...I'm really not sure what to do!?!?!? Thanks

You have "wear through" which is when the finish is pierced and the wood is exposed to the elements. The dark areas are where dirk/water/mud have stained the floor. It is possible to get this out... but probably not all the way. A floor that has wear through needs to be sanded right down, stained (if you wish) and then refinished. Patching can occur...but it is almost always a waste of time because the "look" can be very different from the original sitting right next to it. I don't recommend it for your situation. The second photo shows the deep scratching. Ideally, you would have had your floors looked after BEFORE wear-through occurs. There are some "regular" scratches to the Left in photo 2. You can see it is visible...but no discolouration....THAT is where you draw the line. The darker "wear through" to the Right in photo 2 = too late = full sand and refinish. If you catch it BEFORE wear-through, you can do a "buff and coat". This is a light sanding with a few coats of high end finish over top. The buff and coat is roughly half the price (in Canada at least) as a full sand/refinish. For this reason it is important to catch the floors before you get to this level of scratching.. That being said, you now get to pick some stains (test patch, test patch, test patch). The first photo shows two different woods...you could ask to see if the lighter would could be matched to the darker wood (lots of testing to achieve this). It won't be pefect...but then again you wouldn't have used reclaimed building materials if you were after "perfect". The match can lessen the colour variation to a more manageable (design wise) level. As for "good for dogs" - natural colour of wood = best colour for scratches. A lower gloss (like a satin) can help. You can ask for the "best" finish with scratch resistance that comes in a can. You will pay a premium for it...but it could/should save you thousands of dollars over the long run. A highend, scratch resistant finish means you can get away with the cheaper buff and coats (every 7-12 years...or so) and be able to retain the original (expensive) finish for the full 25 years. The other thing to note: dogs claws require trimming 2-4 PER MONTH when working with hardwoods. This is what the hardwood flooring refers to as "routine" trimming. Some of my clients thought "2-3 PER YEAR" was "routine". I laughed. You have heavy, high energy, powerful dogs. A single lab can cause some damage over time. Two labs can do a number on a floor. Three labs and you have a very short lived hardwood finish. You have 7. I would find the most expensive, scratch resistant finish available in Australia. I would have the maximum amount of finished put your floors (you will pay extra) it and I would budget for a "buff and coat" every 5-7 years.

Get the professional sander guys in to repair the living areas and kitchen but don't go too dark with the stain as it will kill the lovely grain in the matai. I'm thinking a couple of tones richer than the timber knots showing in your photo, definitely no yellow tone at all. In NZ stepping on to carpet especially in a kiwi winter is so much nicer than a cold floor board shock!!! A nice area rug for the lounge and you're done.

Paint your house and ceiling first. You are probably asking for trouble if you put the floors down only to paint over the top of them. If you can, remove the tiles in the kitchen and paint just behind the line of the splashback too. Once painting is done replace kitchen benchtop then splashback. I would call the bathroom its own job and do it individually, unless you only need to paint the ceiling and if a tiler doesn't need to be brought in for anything else in the house? A lot of bathrooms now are getting tiled from floor to the ceiling if this is the case, paint the ceiling first, then tile. If walls need to be painted, it wouldn't really matter if you did them first or last, though if you did it first expect to do some touch-ups. I guess if you really wanted, you could do the first coat before tiles then second after... I don't exactly like stopping and starting painting, so I would do the walls (if they needed to be done) in one hit, after its been tiled. Well that's the order in which I would do everything... Really, for what you're asking, the painting could be done at anytime, but to make life easy on yourself, I would definitely recommend doing it before the floor.