I'm quite lucky that we have quite a large bathroom for over here. There all normally so small in older homes! I have a a lot of space to fill and was only going to use the tiles in the bath and on the floor. I find fully tiled bathrooms very very confining. White wall for the rest, apparently, according to the design guru. But it's ok, I've been told when it comes time to decorate the garage I can have whatever I want!!!!

Thanks for posting new views of your room. You are right, nothing can go in front of the paneling, and we won't block the built-in cubby. In that case let's work with the rest of the space. I found a picture on Houzz for your gallery wall. I think this will allow you to bring in color and texture and interest to your wall without taking up space like furniture would. Try to play with portraits and a couple of paintings in there too - mix it up. Otherwise I would not put anything at the top of that landing (I'd remove that console table). That picture wall should be enough visual interest to your space and it'll draw the eye to the furthest wall as you walk in your house. I would try a small piece with closed storage between the bottom steps and that door by the entry. It looks like the space is no wider than 26", so it'll be a challenge to find something that fits and is tall enough. I would not use the wooden piece you showed above because you want wider proportions and fairly narrow depth so you don't bump into it as you walk by. (something like this ) I would hang a mirror on top of primping. By the cubby you could add a single seat stool. I'm not particularly suggesting these colors for the stool and bombe chest but something along these shapes. At this point if you do that big picture wall and add these two pieces of furniture and a mirror, you might not need to hang anything on the wall above the cubby. Also, I noticed your chandelier is quite substantial for the space and hanging pretty low. Would raising it a little or replacing it by something a little smaller be an option?

Hello There: Your home looks like it has some good bones and period features. No one has yet to comment on marrying subway tiles on lower walls, with tongue and groove cladding on upper walls of your space. I am thinking this finished look could well end up looking quite "busy." Lots of competing "grid" lines, etc. If I understand correctly, this space is actually, or ultimately will be, a bathroom. Perhaps you do not want a wood product on lower sections of the walls because of potential water damage, etc. That said, there are excellent paints, sealants, etc., that you could apply that would guard against this. If painting, using Zinsser Sealant as base coat is a good starting point. As another alternative, you could use much larger tiles on lower portion of walls, oriented vertically. I am thinking 12" x 18" (or 24") tiles. Of course, these are more challenging to install, given their greater size and therefore, weight. Despite this, if you have an excellent tiler, it can definitely be done. For example, you could choose glass tiles, either clear or coloured. Going even further, you could install glass panels to lower sections of walls. You could "back paint" them or not. You could apply paint or even wallpaper (with a wonderful design and colour way you'd likely never tire of) prior to installing glass panels. The wallpaper idea, especially if design is more curvilinear in nature, would not be competing with verticality of tongue and groove, but rather, would complement and enhance it. If beautiful wallpaper (or heck, even a mural or timeless design could be painted directly on walls) is applied and then covered with clear glass panels, the overall effect would be akin to that of an art installation. Naturally, glass panels would be considerably more expensive, but would provide a more seamless, less cluttered appearance. Should you like this idea, simply check what thickness of glass would work best, both for aesthetic and safety purposes. If you have a bit of time to shop around for best supplier and price point, you could well suss out a source that will not "break the bank!" :) To affix glass panels to the walls you want to use hardware that is anodized. As an idea, you could use anodized lug nuts that are usually used for automotive purposes. I just looked up "anodized lug nuts" and see they are available in wide array of wonderful, decorative colours. This hardware would be visibly holding your glass panels in permanent place, but they would be a small attractive design element, ultimately adding another layer of visual interest to your space. I believe glass panels would tie in very well with your great, textured/mottled glass panelled door and transom. Too, I think the overall look would achieve a really attractive marriage as various materials, along with period architectural features would "read:" old, new, and timeless. I realize this design concept may seem counterintuitive to you and/or others, but I can "see it" and think it could be just fab! All The Best, Sharon Black, interior designer and contractor

Thanks for your comments everyone. We've taken your advice (Luke and NH) and changed the island to a rectangle (1200 x 3000). We lose one breakfast bar seat but gain storage and dining room space plus it shortens the distances from the island to the cooktops. It also removes the need for a corner carousel. We're much happier with this result. Dairy_maid, we've done what you suggested and walked through some common tasks. Overall it works reasonably well although we may keep some coffee spoons and butter knives in the scullery drawers for morning toast and coffee. We've also invested in a "silent" rangehood which has the motor on the outside of the house behind the fridge and we've upgraded the scullery sink to one that is 600 x 400 (internal size). Fabrication starts tomorrow. Woohoo. Once again, thanks so much for taking the time to respond. The design has been significantly improved with your input.